Anderson ACCESSORY PLUG & SOCKET

Marine quality all metal parts are nickel plated phosphor bronze. Universal socket/plug will mate with other cigarette lighter type units.

Sea-Dog POWER SOCKET

Chrome steel socket and molder cap with stainless 304 mounting plate. Ideal for additional power outlets.

Perko WATERTIGHT DECK CONNECTION

Chrome plated zinc. Flange gasket with integral waterproof cap for base when plug is removed. Polarized double contact connector. Rated for 15 Amps.

General IGNITION SWITCHES

(Top) Ignition Switch: 3 positions, 3 screw terminals. Ployster housing with chrome hex nut. Brass back-up nut.
(Middle) Ignition/Choke Switch: Derlin body "push-to-choke" feature: 3 positions. 6 boss/screw terminals, Brass back-up nut. Hex black plastic. Replaces OMC #393301 and pollak 33-105.
(Bottom) Ignition Switch: 3 positions, 3 screw terminals. All brass heavy duty ignition starter switch. Spring return.

General HORN SWITCH

chrome plated brass housing. Momentary on-off push button switch. Black plastic button. Ideal for fog horns or sirens. Not ignition protected.

General IGNITION SWITCHES

(Top) Ignition Switch: 3 position. 3 terminals. Polyester housing. Moisture proof heavy duty ignition starter switch.
(Middle) Ignition Switch: 4 position, 4 blade terminals. All brass heavy duty ignition starter switch with chrome hex nut.
(Bottom)Ignition/Choke Switch: Delrin body with push-to-choke feature. 3 positions, 6 wires only potted base. Brass back-up nut. Hex black plastic. Replaces most Mercury.

General PUSH BUTTON SWITCHES

(Top) Chrome plated brass housing. Momentary on-off push button switch. Use for starter, horn or other functions. 2 screw terminals.15 amps.
(Bottom) Heavy Duty, glass reinforced polyester housing. Momentary on-off push button switch. electrical contacts are silver for maximum current carrying capacity. Rubber moisture and dust proof boot nut included. 30 amps.

Cole Hersee PUSH BUTTON SWITCHES

Non corrosive brass construction. 2 positions. On with button depressed, spring return to off.

General PUSH-PULL SWITCHES

(Top) Solid brass construction. 2 positions.
(Middle) Solid brass construction. 3 positions. 3 screw terminals. First pull energizes one curcuit, pull out to second position and both circuits are energized.
(Bottom) Solid brass construction. 3 positions. 4 screw terminals. 2 separate circuits. Use for anchor/running lights or similar functions.

Cole Hersee PUSH BUTTON SWITCHES

(Top)Plasticized body sealed against moisture and dirt. 2 positions. On with button depressed, spring return to off. Black moisture repellant rubber cover which snaps over face nut. 2-18 gauge wire leads.
(Bottom) Non corrosive brass construction. 2 positions. Recessed plunger button within oversized face nut to prevent accidental actuation.

General TOGGLE SWITCHES

(Left) All brass with nickel plated brass face nut and brass back-up nut. 2 positions.
(Middle) Black plastic paddle and locking ring with lever seal and knurled cap nut. sealed to resist water penetration.
(Right) Nickel plated off-on indicator plate; assembled. 2-6"long wire leads. Bat handle.

Cole Hersee PUSH PULL SWITCHES

(Top) All brass construction. 2 positions. Gasket sealed case protects against moisture and dirt.
(Middle) All brass construction. 3 positions, screw terminals. Energizes one circuit in first position and both circuits in second position.
(Bottom)Plasticized body sealed against moisture and dirt. 2 positions. 2-18 gauge insulated copper wire leads 12" long.

General ROCKER SWITCHES

Left and Middle rocker switches are illuminated. Right switch is non-illuminated. All feature: single pole and black plastic design.

Guest BATTERY SWITCHES

(Top) Heavy duty switch. Tough glass-filled polycarbonate case. Rated 360 amps continuous, 600 amps momentary. Selector switch permits selection of either battery, both batteries in parallel or complete disconnection of both batteries.
(Bottom) Heavy duty two position switch with alternator field disconnect. For use where high amperage service is required. Rated 450 amps continuous, 800 amps momentary. Extra heavy duty rated at 600 amps continuous, 1,000 amps momentary

Perko SWITCH PANEL

Black, textured finish. Flexible plastic will mount on flat or curved surfaces. complete with rocker switches, name plates and low profile fuse holders. Rated for 10 amps at 12 volts.

Perko MAIN BATTERY SWITCHES

(Left) Includes a main disconnect switch. Rated 250 amps continuous, 360 amps intermittent.
(Right) Alternator field disconnect model. Prevents damage to the alternator if accidently to the "off" position while the engine is running.

Attwood ROCKER SWITCH PANEL (LIGHTED)

Heavy duty predrilled aluminum plate with plastic rocker switches and indicator lights.

Perko BATTERY SELECTOR SWITCHES
(Left) Same basic feature as listed below.
(Right) Alternator field disconnect model.

Imported SWITCH PANEL

Black backlite panel with chrome plated toggle switches. Wired to common terminal.

Perko HEAVY DUTY BATTERY SELECTOR SWITCH

Same basic features as kisted below. Alternator field disconnect. Fiber reinforced polycarbonate body. Rated 380 amps continuous, 850 amps intermittent(5 minutes on, 5 minutes off).

Perko BATTERY SELECTOR SWITCH

Same basic features as listed below, in addition to 2 extra terminals for use in conjunction with remote indicator panel which determines which batteries are in service. Rated 250 amps continuous, 360 amps intermittent.

Perko Standard features include a make before break design, for use with 2 or more batteries and single or dual engine systems. They permit selection between batteries for starting and charging or operation of both batteries in parallel. They allow the addition of an extra battery for accessories. The "off" position also acts as an emergency disconnect in the event of an electrical problem. In addition some models offer unique options such as keylock for extra theft protection. Surface mount, red plastic housing with large plastic knob. Incorporates an improved design to protect the copper contacts and brass terminals used as electrical connections. For use with systems under 50 volts.